熱搜關鍵詞： 實驗室用小型管式電爐 Furnace 箱式熱處理爐三溫區高溫管式爐

您的位置： 洛陽賽特瑞智能裝備有限公司首頁 > 高溫電爐系列 > 1100℃Ten Heating Zone High Pressure Super-Alloy Tube Furnace with Gas Flow _Pressure Control SystemOTF-1200X-X-85GF -

1100℃Ten Heating Zone High Pressure Super-Alloy Tube Furnace with Gas Flow _Pressure Control SystemOTF-1200X-X-85GF

產品型號：1100℃Ten Heating Zone High Pressure Super-Alloy Tube Furnace with Gas Flow _Pressure Control SystemOTF-1200X-X-85GF

電爐類型：高溫電爐系列

電爐規格：

加熱溫度：

電爐系列：賽特瑞電爐

應用范圍：。

在線咨詢

全國熱線

產品簡介 / Introduction

1100°C Ten Heating Zone High Pressure Super-Alloy Tube Furnace with Gas Flow & Pressure Control System - OTF-1200X-X-85GF

Please view "Isotropic round-wire multifilament cuprate superconductor for generation of magnetic fields above 30 TMat-2014-13-4-Larbalestier-Isotropic round-wire"published by NATURE MATERIAL 3887, 9 MARCH 2014, in which an STR-High-Pressure furnace was used.

OTF-1200X-X-85GFis a high-pressure tube furnace with ten heating zones and pressure amp; gas flow control system. The processing tube is made of Ni-based superalloy (45 mm IDx2400mm L) which can withstand high pressure under bothoxygen and inert gasesupto 1000°C. Its pressure control system can maintain a stable pressure during the heating process which is critical for processing Fe-based superconductive material, or new generation oxide ceramics.

SPECIFICATIONS

Furnace amp; Power	、Splitable Eight heating zone tube furnace with air cooling layer 、High quality fibrous insulation and reflective coating for max. energy saving. 、Power: 208 - 240VAC 50/60Hz, Single Phase, 12KW max. (circuit breaker which is rated 80amps or higher is recommended)
Heating Zone	、Ten heating zones: 150mm / zone 、Total heating zone length: 1500mm 、Constant temp. zone: 900mm ±5°C
Working Temperature	、1100℃max.for ＜ 1hr 、1000℃for continuous 、Heating rate:≤10°C/min
Temperature Control	、Ten digital temperature controllers to control each heating zone 、Each channel is with PID auto-tuning, up to 30 segments programmable 、Built-in overheating amp; thermocouple failure protection. 、+/- 1 oC temperature accuracy.
Heating amp; Cooling Rate	、Heating: 0-200℃ ≤10℃/min , 200-700℃ ≤6℃/min, 700 -900℃ ≤3℃/min, 900-1100℃≤1℃/min 、Cooling: 200-800℃ ≤10℃/min , 800-1100℃ ≤5℃/min
Thermocouple	?Omega3mm OD K Typewith high-temperature (220°C)connector 、Total 10 TCs, one for each zone
Process Vessel	、The pressure vessel is made of Nickel-based superalloy GH747 (Click to downloadGH747 nickel-based alloydatasheet) 、Vessel size: OD 85xID 45xLength 2400 (mm) 、Optional:torque wrench is available hereto avoid over-tighten the flange bolts. Please click the image on the left to order. 、Warning: Never put a sample inside tube directly without crucible or isolated foil to avoid sample react with tube alloy.
Working Pressure	、15 Mpa max. at ＜800°C 、10 Mpa max. at ＜900°C 、6 Mpa max. at ＜1000°C 、4 Mpa max. at ＜1100°C 、Never heat up above 1200°C
Working Gases	、Inert gas and oxygen 、No hydrogen or any flammable gas
Flange and Fitting	、Two CF type flanges are weld with female 1/4"NPT fitting to connect high-pressure tube 、2 pcs Copper o-rings are included ( spare copper O-ring is available as consumable )
Gas Flow amp; Pressure Control System	、Gas flow and pressure control system is built in the separated unit with digital display ( see pic left ) 、Two pressure sensors and digital displays are installed to monitor the pressure for gas inlet and furnace tube 、One high-pressure mass flow controller is installed at the gas outlet to control gas flow rate with max. 10Mpa working pressure and 500 SCCM flow rate 、Pressure relief valves are installed to ensure safety. The valve will release gas when the pressure reaches the setting point.
Dimension amp; Weight	、Dimension: 26000mmL700mmW947mmH(furnace);1100mmL600W1200mmH (control consol) 、Net weight: 480 kg
Operation Instruction
Compliance and Warranty	、NRTLNRTL or CSA certificate is avaialble upon request at extra cost 、One year limited warranty for lifetime support
Application Notes	?Hytort Application, or named Hydroretorting of Shale Oilis a process developed by IGT to double the yield of shale oil and hydrocarbon gases. STR-High-Pressure furnaces with Ni-based superalloy tube is an ideal tool for conducting related experiments. Please click underlined to view research paper.
Safety Notes	、Ni-based Superalloy ( Waspaloy or equivalent)is areliable processing tubewhich can be used under high temperature and high pressure.. It has excellent ductility and tensile property so only creep deformation happens under overpressure destruction test and following by a crack formed (usually at the hot zone at the center of tube) to release the pressure. Brittle fracture won’t happen in the overpressure destruction test which means no tube explosion will happen under overpressure of inert gas or safe gas or under other accidents causing overpressure of inert gas or safe gas. Above pics show Ni-based Super-alloy ( Waspaloy or equivalent)processing tube under overpressure test 、Attention: For the use with flammable, toxic or corrosive gases, you must contact STR-engineering group for the consultation to know all the prerequisites and precautionary measures. 、Attention:A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation.Please click here to learn how to install the gas regulator.

import(/layout/smh/menubottom.html);